ARM-C

Thank you for purchasing a Clockaudio product. We are confident that this product will give you many years of trouble free operation. have been made to further increase the already excellent reliability. It is important not to connect the ARM V2 microphone to an existing ARM-C controller or an existing ARM microphone to an ARM-C MK2 controller.

It will not work. The ARM V2 microphones can only be connected with ARM-C MK2 controllers. The ARM-C controller allows a DSP to instruct up to 4 ARM microphones to be raised or lowered.

Up to four units can be daisy chained (using the Link to DSP input connection). Thus allowing a DSP using a single control line to raise/lower up to 16  Supports 2 x RJ12 ports; one for DSP Input and one for Link which can be used to connect to another ARM-C’s DSP Input. A single command from a DSP will simultaneously activate all connected ARM motorised microphones.  Supports 4 x RJ45 ports (M1 – M4) that allow for fast and easy connection of 4 x ARM motorized microphones.

M1 and M2 on the front of the unit while M3 and M4 are on the rear of the unit.  A positive (+2.5V to +12V) signal applied at the DSP Input port will control unit’s M1 – M4 motor outlet ports.  Logic input to the DSP Input port shall be on pin 2 (Live); pin 1 is Gnd.  Flanges on the unit provide a simple screw fixing of ARM-C controller. 2. Ensure that the Control unit power supply is NOT switched on until all wiring 3. Connect the ARM motorised microphone(s) to any of the M1 – M4 motor outlet ports on the Control unit.

It does not matter which port is used as they are all 4. Connect the DSP logic signal output terminals to the DSP input socket on the ARM-C controller. Use the Link port for daisy chaining the connection to another 5.

Connect the microphone audio output cable to the mixer / DSP. 6. Power up the DSP and check that it has been programmed to supply +2.5V to 12C logic high to ARM-C to raise the microphone. 7. The DSP should be programmed to mute the microphones whilst in the upward 8.

Connect the 12V DC power supply to the DC +/- input terminals of the Controller 9. Switching on the DC supply to the ARM-C controller will illuminate the coloured extend and then retract. This is normal as it will be auto-calibrating. 10.

When a logic high is received from a DSP, the microphone will raise and remain While the front of the unit provides DSP, Link, M1, M2 and power connections, the rear panel provides connection for M3 and M4. The four ARM microphones can be Off the shelf, readymade cables are freely available on the high street electrical retail outlets. However if a cables are required to be handmade, then on the DSP input for the ARM-C, pin 2 shall be used to provide the active signal (Live) while pin 1 provides the ground connection.

None of the other pins are used. and DSP control ports on the controller unit. the DSP during the raising / lowering transitions. (eliminates GSM frequencies from 800 – 1200 MHz) Digital four channel motor control unit for use with the ARM series of motorized Requires a single logic command (+2.5 to +12V) from a DSP or Electronic Switching Unit to raise or lower all ARM microphones simultaneously. o 2 x RJ12 for DSP and Linking to another ARM-C control unit. o 4 x RJ45 M1-M4 motor control ports for 4 x ARM microphones. This product is offered with a 1 year warranty from the date of purchase. Any defect that arises due to faulty materials or workmanship will either be replaced, or repaired free of charge by the agent from whom you purchased the unit.

Please note charges will be incurred on any products returned for service / repair not in warranty or has been subject to customer abuse or incorrect wiring. The warranty does not cover accidental damage, misuse, cabinet parts, knobs, batteries or consumable items. Any product returned to Clockaudio failing to meet the terms listed will The product must be correctly installed and operated in accordance with the instructions The product must be used for the sole purpose that it was designed for.

The warranty given is strictly with the original owner and becomes invalid if the product is Specifications / improvements are subject to change without notice. Clockaudio disclaims any liability for incidental or consequential damages. The warranty is in addition to and does not diminish your statutory legal rights.

At the end of the life of this equipment, dispose of equipment according to local